Reasons to Change Door Lock
There are many reasons to change the lock on your door, from increasing your home’s security to redecorating your entrance. You may also need to change locks if your key gets stuck in the lock or is difficult to turn.
Changing your lock is a simple project that even beginner DIY homeowners can tackle. To start, gather the necessary materials.
Remove the old lock
Removal of the lock that was in place before the door is an essential step before installing the new lock. This is especially crucial if you suspect that someone else has access to your home. It’s also a good idea after you’ve moved into your new house, had a break-in or a roommate moved in. It’s much more simple than you think and can be completed in just a few minutes.
Begin by taking off the screws that secure the deadbolt faceplate onto the door frame. To remove the faceplate, you will have to remove screws from both sides. This will allow you see the inside of the door and give you an understanding of how to continue with the remaining steps.
After removing the old faceplate you must take off the bolt, strike plate and the strike plate. Remove the bolt from the door hole by using the screwdriver. If the bolt is rusty, you may need to use a chisel hammer it out. If you’re using a chisel be cautious not to scratch the door frame.
Make sure that the new doorknob, deadbolt and lock will fit into the holes that are already present in the door before removing the old one. Many hardware stores and large box stores stock a range of locks and will help you choose the right one. Get help if the lock you bought does not fit your door.
While you are removing the lock that was previously in use, look for small notches or depressions in the handle or around the trim. If you can find them, slip a straightened safety pin or flat screwdriver into them to open the handle and expose screws underneath.
Once the screw inside the handle has been removed you can begin removing the knob from its spindle. To do this, locate the set screw that is located on the knob’s base and loosen it. Then, remove the spindle.
Install the new lock
It’s a good idea to change the locks on your doors periodically, especially if you have been the victim of a break-in. It is easy, cheap and efficient to change the lock on your door. With a screwdriver, and a few basic steps the majority of people can do it themselves. Depending on the circumstances you might also need to learn how to rekey a door lock so that only you have the key.
To start the process, you need to buy an additional lock that matches the keyway on your existing lock. Many locksmiths will replace your lock at an additional cost however, you can save money by doing this yourself. You can buy a new lock at a hardware store or on the internet. Standard deadbolts will fit most doors. However, you’ll have to measure your door to ensure that it fits.
Your new lock will often come with a diagram that will show how to put it on the door. You can use it as a reference when drilling the hole, which is much more convenient than measuring each time. If the template does not align with your hole, you can take it back to the shop and get another one.
When you install the new lock, you must be sure to place it on the right side of the door. Check the latch. It should be marked with “up” or similar. Make sure that the latch is seated correctly in the plate, and then fix it using the supplied screws.
If you’re replacing locks on doors it is also essential to pay attention to the way it’s operated. Most knob locks are left-handed, however there are a few that are right-handed. If you’re not careful, you could put the knob on the wrong side of the door, which will prevent you from locking it from inside or outside.
You should test the new lock once you finish. You should be able to lock the door from both the inside and outside, and unlock it with keys. If you’re not happy with the result you can always contact a professional locksmith to repair upvc window lock it.
Test the lock
If a lock on your door isn’t able to be opened can be frustrating, it can also put your family’s security at risk. It’s simple to solve the majority of door lock issues by tackling the issue and lubrication. Make sure that the key is properly cut and the lock assembly isn’t loose or dirty. If this doesn’t solve the problem, you can try to lubricate the door lock actuator using powdered graphite or a silicone-based oil.
Check that the door lock switch, wiring harnesses, and the actuator connector are all working correctly. To check this, refer to the manual or wiring diagram to determine the purpose and color-coding for all the door lock switch wires. Utilize a digital meter or test light to determine if the actuator is receiving power and ground when the switches are turned on. If you see voltage switches that toggle with each other, it means the switches are in good working order and the actuator will require replacement.
If the switch appears to work but the actuator doesn’t move when you turn the knob, it could be an issue with the cylinder itself. The actuator cylinder is fitted with pins that are spring loaded. They stop the cylinder from turning until the key is inserted and then they push them upwards to meet the height of the key at that location. Then, the cylinder to turn and open the lock body and allow the handle to latch.
If the door lock actuator is still inoperable, you can remove the switch and wires from the actuator by using small screwdrivers to unlock the locking bolt and separate the plastic cover that holds the electrical connector. Then disconnect the door lock actuator and let it fall. Then, you should be able find the two bolts in 10mm that hold the actuator in place and remove them. Once the actuator has been removed and the electrical connector disconnected, you can remove it. black electrical connector.
Replace the key
If you have a keyed deadbolt or door knob if it is not functioning properly, you must either change the lock’s key or rekey it or replace it completely. This is not difficult and will save you money. But, prior to doing this, it’s an excellent idea to have a locksmith examine the locks and check them for any issues. This will give peace of mind knowing that your home is safe and secure.
To begin, remove the faceplate that is on the outside of the doorknob or deadbolt. There may be screws that are holding it in place, so use a screwdriver to loosen them, and then pull the faceplate away. Next you can use a flat-head screwdriver to remove the inside faceplate. Once you have removed your faceplate, you can remove the bolt and a screw from the lock cylinder.
A locksmith can help you determine if the lock you have requires replacement or rekeyed. They can also offer guidance on the most effective security measures for your home. They can also make any needed modifications to the door and frame to ensure a perfect fit. They will also provide a guarantee on their work.
If you choose to rekey the double glazing upvc window locking mechanism repair lock repairs – Telegra.ph,, you’ll need to purchase an additional key for it. It is crucial to select the lock key that fits snugly. A key that is not the right size may harm the internal mechanism of the lock and prevent it from working. Insert the key into the lock to verify its size. If it is in a flush with the plug it’s the right size. If the pins protrude out of the top of the plug, they’re not long.
There are many reasons why you might want to change the lock on your door, including:
If you’re moving into a former owner’s residence or have lost keys, rekeying your lock is an economical alternative than replacing it. It’s also more cost-effective than a complete replacement window lock. Rekeying a lock that is already in use may not be feasible in certain circumstances. If the lock has been damaged or jammed repeatedly, for example, it may be time to replace it.